DLPA2000
- High Efficiency RGB LED/Lamp Driver with Buck-Boost DC-to-DC Converter, DMD Supplies, DPP Core Supply, 1.8-V Load Switch, and Measurement System in a Small Chip-Scale Package
- Three Low-Impedance (30 mΩ Typical at 27°C) MOSFET Switches for Channel Selection
- Independent, 10-Bit Current Control per Channel
- 750-mA Max LED Current for DLPA2000 Embedded Applications
- On-Chip Motor Driver
- DMD Regulators
- Requires Only a Single Inductor
- VOFS: 10 V
- VBIAS: 18 V
- VRST: –14 V
- Passive Discharge to GND When Disabled
- DPP 1.1-V Core Supply
- Synchronous Step-Down Converter with Integrated Switching FETs
- Supports up to 600-mA Output Current
- VLED Buck Boost Converter
- Power Save Mode at Light Load Current
- Low-Impedance Load Switch
- VIN Range from 1.8 V to 3.6 V
- Supports up to 200 mA of Current
- Passive Discharge to GND When Disabled
- DMD Reset Signal Generation and Power Supply Sequencing
- 33-MHz Serial Peripheral Interface (SPI)
- Multiplexer for Measuring Analog Signals
- Battery Voltage
- LED Voltage, LED Current
- Light Sensor (for White Point Correction)
- Internal Reference Voltage
- External (Thermistor) Temperature Sensor
- Monitoring and Protection Circuits
- Hot Die Warning and Thermal
- Low-Battery Warning
- Programmable Battery Undervoltage Lockout (UVLO)
- Load Switch UVLO
- Overcurrent and Undervoltage Protection
- DLPA2000 DSBGA Package
- 56-Ball 0.4-mm Pitch
- Die Size: 3.280 mm × 3.484 mm ± 0.03 mm
The DLPA2000 is a dedicated PMIC/RGB LED/lamp driver for the DLP2010 and DLP2010NIR digital micromirror devices (DMD) when used with a DLPC3430, DLPC3435, or DLPC150 digital controller. For reliable operation of these chipsets, it is mandatory to use the DLPA2000.
Technical documentation
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
DLP-PICO-FW-SEL — DLP® Pico™ Firmware Selector
DMD-DIFFRACTION-EFFICIENCY-CALCULATOR — Calculator helps model DMD diffraction patterns and diffraction efficiency
Supported products & hardware
Products
Multi-channel ICs (PMICs)
Home cinema, business & education DMDs
Portable & consumer DMDs
UV (<420nm) DMDs
Pro-AV & large venue DMDs
Exterior lighting & projection DMDs
NIR (>700nm) DMDs
Interior display DMDs
Visible (420 to 700nm) DMDs
DLP controllers & drivers
Hardware development
Evaluation board
Development kit
Support software
DLP-OMM-SEARCH — DLP® Products third-party search tools
DLP-OPTICAL-DESIGN — DLP-OPTICAL-DESIGN-GUIDELINES
Supported products & hardware
Products
Multi-channel ICs (PMICs)
Home cinema, business & education DMDs
Portable & consumer DMDs
UV (<420nm) DMDs
Pro-AV & large venue DMDs
Exterior lighting & projection DMDs
NIR (>700nm) DMDs
Interior display DMDs
Visible (420 to 700nm) DMDs
DLP controllers & drivers
Hardware development
Evaluation board
Development kit
Support software
TIDA-00722 — Real-time Color Management Reference Design Using MSP430 for TI DLP® Pico™ Projector
TIDA-00325 — Ultra Mobile, Ultra Low Power Display Reference Design Using DLP® Technology
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| DSBGA (YFF) | 56 | Ultra Librarian |
Ordering & quality
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.